Jump to content

Pennsylvania Railroad class N1s

From Wikipedia, the free encyclopedia
Pennsylvania Railroad N1s
PRR N1s #7246 at Youngstown, Ohio in 1919, when less than a year old. Note the Lines West central headlight (later relocated higher) and high slope-sided tender coal space
Type and origin
Power typeSteam
BuilderALCO-Brooks (35),
Baldwin Locomotive Works (25)
Build date1918–1919
Total produced60
Specifications
Configuration:
 • Whyte2-10-2
 • UIC1'E1'h2g
Gauge4 ft 8+12 in (1,435 mm)
Leading dia.33 in (0.838 m)
Driver dia.62 in (1.575 m)
Trailing dia.36 in (0.914 m)
WheelbaseLocomotive: 41 ft 11+12 in (12.79 m)
Length91 ft 4+58 in (27.85 m)
Axle load75,600 lb (34,300 kg; 34.3 t)
Adhesive weight351,000 lb (159,000 kg; 159 t)
Loco weight435,000 lb (197,000 kg; 197 t)
Tender weightEmpty: 86,800 lb (39,400 kg; 39.4 t);
Loaded: 206,100 lb (93,500 kg; 93.5 t)
Tender type100 F 85
Fuel typeCoal
Fuel capacity39,300 lb (17,800 kg; 17.8 t)
Water cap.9,600 US gal (36,000 L; 8,000 imp gal)
Firebox:
 • Grate area79.9 sq ft (7.4 m2)
Boiler pressure215 psi (1.48 MPa)
CylindersTwo
Cylinder size30 in × 32 in (762 mm × 813 mm)
Valve gearWalschaerts
Valve typePiston
Performance figures
Maximum speed35 mph (56 km/h)
Tractive effort84,890 lbf (377.61 kN)
Factor of adh.4.13
Career
LocaleMidwest (Illinois Indiana, Ohio)
Retiredby 1950
DispositionAll scrapped

The Pennsylvania Railroad (PRR) N1s was a class of 2-10-2 "Santa Fe" steam locomotives built for the Pennsylvania's Lines West. 60 engines were built between December 1918 and November 1919, and worked heavy mineral freight to and from ports on the Great Lakes until their retirement in the late 1940s. All examples were scrapped by 1950.[1]

Overview

[edit]

The 2-10-2 wheel arrangement, ten driving wheels with a two-wheel leading truck and a two-wheel cast KW-pattern trailing truck under a large Belpaire firebox, suited the N1s' intended purpose well. They were drag freight engines, designed to haul heavy freight up the 0.3% grade leading out of the PRR's "Lake ports," and were rated at 6000 tons (5443 tonnes) on these relatively easy grades.[1] The design was developed by the PRR's Fort Wayne Shops and orders were placed with Alco (Brooks) (35 locomotives) and Baldwin (25 locomotives) for a total of 60; the first Alco locomotive was delivered in December 1918, with the remainder arriving during 1919.

The N1s was a large locomotive; the boiler was the largest then used on any non-experimental PRR locomotive, and the firebox had 79.9 square feet (7.4 m2) of grate area and a 5-foot (1.52 m) long combustion chamber. No feedwater heater was fitted, but a mechanical stoker and power reverse were installed, being necessities on such a large locomotive. Boiler pressure was initially set at 205 pounds per square inch (1.41 MPa), but was quickly raised to 215 pounds per square inch (1.48 MPa).[1] The boiler was reportedly designed to take a pressure of 250 psi (1.72 MPa), but whether it attained this pressure in service is not known.[citation needed]

PRR N1s #8363 in its official builders' photo.

To allow the locomotive to negotiate tight 22-degree curves, the first and fifth driving axles were fitted with lateral motion devices and the center axle was blind.[1]

Comparison

[edit]

In many respects, the N1s was similar to the I1s 2-10-0 "Decapod". Driver diameter was identical, and the cylinders on the I1s were a mere 0.5 in (13 mm) wider, having the same stroke of 32 in (810 mm).[2] The N1s had a longer boiler at 20.83 ft (6,350 mm) long, but the I1s used a higher working pressure of 250 psi (1.7 MPa). The I1s' tractive effort was higher, at just over 102,000 lbf (450 kN), but the N1s had a superior factor of adhesion—4.13 to the I1s' 3.28, suggesting the N1s had less of a tendency to slip than the Decapod. The N1s, as a low speed drag hauler, was limited to 35 mph (56 km/h), while the I1s was capable of 50 mph (80 km/h) or greater.

Disposition

[edit]

The N1s were the first class of large power withdrawn after diesel locomotives appeared, as diesels proved superior at the low-speed "lugging" the N1s was designed for. All were scrapped by 1950.

See also

[edit]

References

[edit]
  1. ^ a b c d "Pennsylvania 2-10-2 "Santa Fe" Locomotives in the USA". www.steamlocomotive.com. Retrieved 2024-04-16.
  2. ^ "Pennsylvania 2-10-0 "Decapod" Locomotives in the USA". www.steamlocomotive.com. Retrieved 2024-04-16.